How To Measure Garage Door Torsion Springs: A Comprehensive Guide

garage door torsion springs are an important part of your garage door system. They help to keep the door in balance and ensure that it opens and closes smoothly. If your garage door torsion springs are not working properly, it can cause a lot of problems. In this blog post, we will teach you how to measure garage door torsion springs so that you can determine if they need to be replaced.

garage door torsion springs are located above the garage door. There are usually two of them, one on each side of the door. In order to measure garage door torsion springs, you will need a tape measure and a helper. First, find the center of the garage door and measure from there to the end of each spring. Then, measure the width of the garage door. Finally, determine the height of the garage door by measuring from the ground to the top of the garage door.

Once you have these measurements, you can use a torsion springs size chart to find out what size springs you need. If your garage door is old or has been damaged, it is possible that the springs are not the correct size. In this case, you will need to replace them with new garage door torsion springs.

If you are not sure how to measure garage door torsion springs, or if you need help selecting the right size springs, please contact a garage door professional. They will be able to help you get the right measurements and select the correct springs for your garage door.

How do I know what spring to get for my garage door?

There are a few things to consider when selecting garage door torsion springs. The most important is the weight of your garage door. You need to make sure that the new springs can support the weight of the door. Other factors to consider include the height and width of the garage door, as well as its age and condition.

What size is my garage door spring?

The size of your garage door spring will depend on the weight and height of your garage door. You can use a torsion springs size chart to find the right size for your door. If you are not sure what size to get, or if you have any other questions, please contact a garage door professional.

What size torsion spring for 16’x7 garage door?

A 16’x garage door will require two springs with a total length of 96″. You can find this size in the 100″ section of our torsion springs size chart. If you are not sure which springs to get, or if you have any other questions, please contact a garage door professional.

Garage door torsion spring length importance?

The length of your garage door torsion springs is very important. They must be the correct size to support the weight of your garage door. If they are not the right size, it can cause problems with the balance of the door and could lead to serious injury. It is important to get the correct measurements and select the right size springs for your garage door.

Can I change the garage door torsion spring length?

It is possible to change the garage door torsion spring length, but it is not recommended. If the springs are not the correct size, it can cause problems with the balance of the garage door and could lead to serious injury. It is important to get the correct measurements and select the right size springs for your garage door.

Can I reuse garage door torsion springs?

It is possible to reuse garage door torsion springs, but it is not recommended. If the springs are not in good condition, they could break and cause serious injury. It is important to get new garage door torsion springs if your old ones are not in good condition.

What garage door torsion spring brand is the best?

There is no one “best” garage door torsion spring brand. It is important to select a brand that you trust and that has a good reputation. If you are not sure which brand to choose, or if you have any other questions, please contact us.

Read More…

For everyone with garage doors in their commercial and residential property, having the right measurement of torsion springs are essential.

You typically activate your garage door several times a day.

Hence, your garage door’s mechanical components also work continually.

Consequently, the components will inevitably incur damages, and the spring isn’t safe from the gradual wear and tear.

With each movement, your garage door spring coils extend and release while subsequently wounding up.

Although garage door torsion springs are durable and can endure such demanding activity, the continual movement can eventually cause them to break and fail.

Finally, you will have to make a move and replace or adjust your garage door torsion springs to keep the system functional.

However, in order to get new torsion springs for your garage door, there are things you need to prepare first.

Since there are numerous torsion springs from various manufacturers in the market, it’s vital to know the right measurement for your garage doors.

So, it’s best if you learned how to measure garage door torsion springs to make the replacement process quick.

Here’s what you should do to get accurate measurements for your garage door torsion springs.

Identifying Torsion Springs’ Wind Direction

Before you go out to purchase a replacement for your garage door torsion spring, you must first know its wind direction.

Through this, you can efficiently choose whether you need a right-wound or a left-wound spring for replacement or both.

If you look inside your garage door, you will see two distinct springs next to the opposite portion of the bar hanging over the door.

Typically, there’s an exclusive stationary cone between the right-wound and left-wound springs, which separates them from each other.

But how can you identify if it’s a left-wound or a right-wound spring?

You can check the springs’ endpoint direction.

If it’s pointing in a counter-clockwise direction, it’s a right-wound spring— otherwise, it’s left-wound.

It’s very important to identify the right wind direction as this can affect your garage door operation.

If you get the wrong spring, it will cause your garage door to malfunction.

Measuring the Spring’s Inside-Diameter and Overall Length

Generally, this process might be easy as most garage doors have markings of these measurements.

Look for the markings engraved on the stationary or winding cone.

You may see numbers like 1.75 or 2.0.

If so, then you now know the diameter of the spring.

However, if such a figure does not appear on the winding cone, you will need to measure the spring yourself.

You can position the spring on a flat surface and use a ruler or measuring tape to determine its inside diameter.

It’s also important to measure the overall length of your garage door torsion spring.

The spring’s length is crucial to its winding capacity.

Determining the Wire Size

Measuring the wire size is quite simple.

You just have to run the tape measure through the distance between the first 10 and 20 coils.

Once you get the measurement, you should then compare it to a standard wire size chart to determine the right length.

You can browse the internet for comparison charts.

Identifying Color Code

Your garage door springs have color codes.

This color code system helps in the accurate identification of springs for repair and replacement.

It usually does not affect your garage door’s operations since it’s only a technical identification system.

As for your garage door torsion springs, this color code system tells whether it’s left wind or right wind.

The black typically signifies the right wind, while the red corresponds to the left-wind spring.

Also, the color-coding helps the technicians servicing the garage door determine the wire’s thickness or gauge.

Let Certified Technicians Handle Your Torsion Springs Measurement and Replacement

Measuring your garage door torsion springs might take much of your time.

Although you can do the job on your own, the best way to avoid all the hassle is to let Vancouver Overhead Doors deal with it for you.

Sure, you can learn how to measure garage door springs.

However, the work doesn’t stop there.

After getting the right measurement, you’ll have to buy the new component and replace the old one.

The replacement job comes with risks as you’re dealing with springs that are under tension.

You might encounter accidents during the process and cause damages to your property.

Hence, it is best to rely on certified technicians to measure and replace your torsion springs.

At Vancouver Overhead Doors, we ensure safety and customer satisfaction all at once.

Call us to schedule an appointment with our technicians!